Above all, there are three factors that determine the likelihood of Legionella bacteria colonising a water system:
- Water temperature;
- Cleanliness; i.e. availability of nutrients and shelter;
- Water age; i.e. the rate of water movement & turnover within a system.
Much like a game of rock-paper-scissors no single one of these factors can trump the others in importance.
Water temperature control is made more difficult in a dirty system where the temperature can not penetrate the sediment or where the movement of water is restricted so that hot water cools and cold water warms up. A clean system is all very well, but if the water temperature is not controlled or if water is allowed to stagnate then bacteria will find a place to grow.
Finally, even where water turnover is high, bacteria will find a place of shelter amongst sediment and sludge or hide out in pockets of the system that struggle to achieve the required temperature.
In most cases, the control of legionella bacteria can be achieved by considering these three concerns and addressing any shortfalls in the design, installation, maintenance or operational performance of the water system. In this blog we look at ways in which regular movement of water can be achieved.
Right First Time
“Right first time” has become a bit of a catchphrase here at the Water Hygiene Centre. Successful water safety begins with correct design and installation of water systems. Failures at the first hurdle result in water systems that are inherently more risky, and therefore more troublesome, throughout their life cycle. HSG274 Part 2 states that “storage tanks, water heaters, pipework and components and associated equipment containing water” should be “designed to avoid water stagnation by ensuring flow through all parts of the system”.
Well-designed water systems that are properly installed and commissioned can minimise the potential for stagnation, which can be caused by a vast range of design and engineering defects, some examples of which include:
- oversized storage vessels - in particular where there is more than 24-hours storage capacity;
- uneven flow through parallel storage vessels;
- oversized pipes or excessively long pipe runs;
- pipework constrictions;
- unauthorised isolation of services;
- unbalanced hot water circulation;
- standby equipment;
- low draw-off outlets positioned at the end of the line e.g. water coolers or ice-making machines;
- over-provision of services resulting in reduced frequency of use.
Whilst operational estate managers may have the necessary authority and resources to correct physical defects, often, designers and project managers are able to address these defects either on the drawing board or at least before water systems enter service. This leaves operational managers to devise and implement a programme of inspection and testing that will determine the operational temperature performance and hygienic condition of a water system; however, when it comes to identifying those outlets that are simply underused by the building occupants things start to become a little more difficult.
Little used outlets
In the workplace, there may be outlets that are required for operational, welfare or safety purposes that do not receive regular and frequent use and/or areas that are temporarily out of use. Estates managers require the assistance of building occupants to identify them and whilst in some cases estates teams will have the resources to implement a legionella flushing regime, in others this duty will fall to the building occupants themselves.
Any outlet that is subject to infrequent or intermittent use is classed as a little used outlet. The definition of “infrequent use” may vary between applications and will depend not only on frequency and duration of use, but also other risk factors, such as water temperature and the vulnerability of the population.
The Health & Safety Executive’s HSG274 Legionnaires’ Disease: Technical Guidance Part 2 states that any outlet “not used for a period equal to or greater than seven days” should be classed as a little used outlet and that “for high risk populations, e.g. healthcare and care homes, more frequent flushing may be required as indicated by the risk assessment”.
For healthcare premises, the Department of Health’s HTM04-01 Part B: Operational Management states “water draw-off should form part of the daily cleaning process. The procedure for such practice should be fully documented and covered by written instructions”.
HTM04-01 also states “During the temporary closure of wards or departments, a flushing regime should be instigated to maintain system hygiene. Flushing should be continued until stable temperatures are achieved. Advice and guidance is also provided in BSI’s PD855468”.
According to PD855468, ‘hygiene flushing’ (i.e. drawing off water for the avoidance of stagnation) should be carried out weekly or “twice weekly in healthcare premises”.
The Hierarchy of Control
Where little used outlets are identified, it should first be established if the outlets are surplus to requirements. If no longer required, outlets should be removed – ensuring that all associated supply pipework is taken out and that no live dead-end pipework remains in situ.
Where this cannot be achieved a regular legionella flushing regime will be required.
Reasons for a legionella flushing regime
Periodically flushing outlets can be an effective means of achieving a regular changeover of the water contained in the little used outlet and its associated supply pipework, this ensures:
- Introduction of fresh cold water containing residual disinfectant, either from the mains supply or from a supplementary water treatment system, if fitted;
- Regular exposure of hot water pipework to temperatures at which Legionella and other bacteria are discouraged;
- Disturbance of biofilms through the sheering action of running water.
Process for flushing
A legionella flushing regime should be devised as part of the organisations “written scheme of precautions” or “water safety plan” and will need to take account of:
- the responsibility structure for management & execution of the programme including arrangements for holiday cover and absenteeism;
- the technical specification for the task;
- the task risk assessment & safe method of work, i.e. how to flush outlets safely;
- process for identifying little used outlets and keeping the list of outlets under review;
- training requirements for personnel carrying out flushing activities and those supervising them;
- training and supervision of operatives carrying out flushing activities;
- record keeping requirements.
The HSG274 Part 2 and HTM04-01 Part B guidance both advise that outlets should be flushed “until the temperature at the outlet stabilises and is comparable to supply water”. The time that this takes in practice will depend on a range of variables including:
- length of the supply pipework;
- ambient temperature;
- frequency of use;
- localised heat sources;
- quality of pipework insulation
- flow rate.
The list could go on… let’s just say the duration for flushing will vary between installations!
HTM04-01 adds that regular flushing applies to all infrequently used outlets and that monitoring water temperature when flushing “may assist in identifying where additional flushing is necessary”.
The guidance recommends that flushing is carried out at least weekly but also suggests that risk assessments should be used to determine if flushing is required more frequently. For example, it is not uncommon in healthcare premises to find that the routine flushing of little used outlets is carried out twice weekly or even daily where a particular risk has been identified.
Exposure to Aerosols
Water emitted from the outlet during flushing should be purged to drain safely. In order to reduce the risk of exposure to Legionella bacteria the British Standards Institutes guidance document PD855468 suggests “flushing should be carried out in a safe manner which minimises aerosol production e.g. removing showerheads prior to flushing”.
HSG274 highlights concerns that lapsed flushing programmes “can result in a critical increase in legionella at the outlet”. Either hard-copy or electronic records are acceptable as long as they include details of:
- a list of the individual outlets to be flushed;
- the date, time and duration of flushing;
- the initials of the person carrying out the work;
- the water temperature achieved;
- biocide concentration, if applicable;
- any faults and other observations;
- further actions required;
- sign-off by an authorised person.
In addition to the flushing task records, all staff training should be recorded.
When can we stop flushing?
For occupied areas checks should be made with local staff to ensure that the list of little used outlets reflects current practices and usage levels. Outlets should be added and removed from the list as necessary. As such a regular review of the scheme and the list of outlets is required to ensure they remain up to date.
Management reporting procedures should be in place to ensure that flushing teams are kept abreast of changes in building and/or department occupancy.
The prevention of stagnation within water systems starts on the drawing board. Good design practices are essential to minimise resource intensive control measures & remedial works later on.
It might not sound difficult to flush water from a tap, and perhaps this leads to complacency amongst duty holders, but developing and implementing a dynamic & effective system for identifying little used outlets can be difficult. It requires ongoing leadership, communication and cooperation throughout organisations to nail it down. In our experience, there is no “one-size fits all” solution but organisations could start by identifying the key players and bringing them into the discussion. Including:
- those who can provide information on whether outlets are used or not;
- those responsible for administering & managing the flushing programmes;
- those responsible for operational maintenance of the water systems;
- designers and installers.
Some or all of these stakeholders may already be members of an organisations Water Safety Group, which is the ideal forum for such discussions.
If you have questions regarding the issues raised above or you would like to speak with one of our consultants please click here to get in touch.
Editors Note: The information provided in this blog is correct at date of original publication - April 2018.
© Water Hygiene Centre 2019